
Product code: 32001.190.68.CZ
€325.87
Buying for a business or in larger quantities? Request a B2B quote
The panel's straight edge sits flush with the arris of the corner, and the hand reaches around the corner onto the adjacent wall, so the figure looks as if it's hiding behind the house and peeking out. The effect works within a range of 30–150° relative to the wall with the panel; outside that angle you only see the sheet metal from the side. From 15 m, the 190 cm silhouette looks like a person standing behind the building.
This silhouette works only on an outside corner on the left side and will not work on a flat wall or an inside corner. Measure before ordering: 88 cm of clear wall to the side of the corner, 220 cm up from the ground, and a corner plumb deviation of less than 5 mm over the full height of the panel.
A skeleton in a standing pose, leaning out from behind a corner: a skull with eye sockets, a ribcage with ribs cut all the way through, and a bony hand gripping the corner of the building with fingers curled around the adjacent wall.
A single piece cut from 3 mm sheet steel, with no welds, bends or added parts. Every detail is a through-cut opening, and the open area makes up 66% of the silhouette's surface. Not a single screw, mounting hole or bracket is visible from the front: the panel hangs on spacers hidden behind it and casts its own shadow on the plaster.
Product details
| Parameter | Value | What it means |
|---|---|---|
| Dimensions | 68 × 190 cm | you need a clear stretch of wall 88 cm to the side and 220 cm up |
| Weight | 10,4 kg | for designs over 150 cm, installation takes two people |
| Material surface area | 0,44 m² | in a 100 km/h wind, a force equivalent to about 21 kg |
| Openness | 66% of the silhouette's surface | that much of the plaster shows through the cut-outs |
| Corner side | left | the straight edge of the panel sits flush with the corner on this side |
| Sheet thickness | 3 mm | the panel does not flutter in the wind and needs no frame |
The fixing has to pass through the insulation and anchor into the load-bearing layer — a plug in the polystyrene alone will not hold 10.4 kg. The first installation takes about 60 minutes, and each following season a few minutes, because the anchors stay in the wall. Every hole in the facade layer must be sealed: an unsealed hole lets water in under the plaster, and at the first frost the freezing water detaches it around the hole.
Matte black is the finish the effect is built on — a dark silhouette on light plaster reads as a shadow. Corten gives a rusty figure that looks like a sculpture, but for the first 6–12 months it stains the plaster beneath the panel, so on a light facade choose black.
The powder coating does not wear off from water or frost; Corten has no coating, because the patina itself stops corrosion beneath it. After the season, the panel comes off the anchors and can be stored flat — it is only 3 mm thick. The manufacturer is Metal4Home, a brand of Adjatech Metalworking Sp. z o.o., a maker of metal decorations from Poznań.
Questions and answers
Only on an outside corner and only on the left side — the straight edge of the panel must sit flush with the edge of the corner, and 2 cm of plaster between them is enough to make the effect disappear. You need a clear stretch of wall 88 cm to the side of the corner and 220 cm up from the ground.
Not on the insulation alone — a plug set in 12–20 cm of polystyrene will not hold a panel weighing 10.4 kg. The fixing must pass through the insulation and anchor into the load-bearing layer under the plaster. You can check the insulation thickness with a test drilling under the windowsill.
In a 100 km/h wind, a force equivalent to about 21 kg acts on the 0.44 m² material surface, which is more than the panel's own weight. That is why the number and type of fixings are a structural decision here, not a matter of convenience.
Matte black on a light facade — the dark silhouette reads as a shadow, and from 15 m you cannot tell it is sheet metal. Corten gives a rusty figure that looks like a sculpture, but for the first 6–12 months the patina runs off with the rain and stains the plaster beneath the panel. On white and cream plaster, choose black.
| Finishes: | Corten, Black |
|---|---|
| Dimensions: | 68×190 cm |
| Finish and color | |
| Size | |
| Mounting and display | Outdoor (weather-resistant) |
| Themes | |
| Room | Garden, Facade and entrance |
We use cookies to make it easier for you to navigate and to enable certain features. You will find detailed information about all cookies below under each consent category.
Cookies classified as "necessary" are stored in your browser because they are essential for enabling the basic functionality of the website.
We also use third-party cookies that help us analyze how you use this website, store your preferences, and deliver content and ads that are relevant to you. These cookies will be stored in your browser only with your prior consent.
You can enable or disable some or all of these cookies, but disabling some of them may affect your browsing experience.
