Spooky Halloween decorations where the light works from four sides at once: a 3 mm steel silhouette stands on a round base with a diameter of 24 cm, with four tealights burning around it. The manufacturer is Metal4Home, a brand of Adjatech Metalworking Sp. z o.o., a maker of metal decorations from Poznań, and parcels are shipped from Janikowo near Poznań.
Why four flames instead of one
One candle gives a single point of light and one direction of shadow — the silhouette then reads only from the front, and from the side it turns into a 3 mm wide strip of sheet metal. Four tealights placed on the diagonals of the base light the plate from every side: the two front ones draw the face and the cut-outs, the two rear ones cast a glow on the edges, so the outline is visible from across the table as well. That is the whole difference between this product and a single-candle holder, and the first thing worth checking once you light it.
How many hours the set of tealights burns
The four tealights burn at the same time, so the set gives 4 hours of light, not sixteen — sixteen is the combined burn time of all four, and that figure only tells you about wax consumption. A typical tealight holds 12–14 grams of wax and burns for about 4 hours, which is from dusk to the end of dinner. Hours are a better unit here than lumens, because nobody buys a candle holder by its luminous flux, only by whether it will last through the evening.
Three parts, no tools, no screws
The candle holder is exactly three flat steel sheets: a Ø 24 cm base, a plate with the silhouette and a 16 × 16 cm stabilizing fin. The plate and the fin cross at a right angle on a slot cut halfway into each of them, and both fit into the base on short tabs. Assembly takes a few seconds and requires nothing but your hands — no welds, screws or bought-in parts, so there is nothing to lose either.
The fin is not a decoration
A smooth 16 × 16 cm pointed arch, the same in all eleven designs, gives the silhouette stability on the second axis. Without it, a flat 30 cm tall sheet would topple at the slightest tug on the tablecloth; with it, the candle holder stands on two planes set crosswise and behaves like a three-dimensional object, not a cutout. With the bat, whose wings extend 3 cm beyond the outline of the base, the fin is the only reason the whole thing doesn't tip over.
Where to place the candle holder at the table
In the middle of the table, not at the edge: with the sockets spaced on the diagonals, two flames always end up on the side of the diners and two on the opposite side, so the silhouette is lit from both directions only when it has 30 cm of free space all around. On a 90 cm wide table that leaves 33 cm for plates on each side. Placed against a wall, the two back flames stop doing their job and the product loses half of what you pay for.
Halloween decorations that come back for the tenth year
Among Halloween decorations, this is the only group where you buy the product once: 3 mm steel doesn't shatter when it tips over, doesn't melt in a flame, and doesn't yellow like lacquer on glass. The matte black finish is a powder coating 60–80 micrometers thick; after ten seasons it's the same shade as on delivery day. A glass candle holder of this size survives one fall off the table, while a ceramic one cracks the first time it hits an edge — the table below puts numbers on it.
One body, eleven silhouettes
The base, fin, sockets and joining method are identical across all designs — the only difference is the plate with the silhouette. Two or three candle holders set on one table read as a series, because they share the same round base and the same candle line height. With twelve flames from three sets, the same table gets 4 hours of glow and light from twelve points instead of four.
What's left after the season
Three flat sheets with a combined thickness of 9 mm that fit in the drawer next to the tablecloths. The largest piece is the base disc, 24 cm in diameter, so the whole set takes up less room than a dinner plate. A glass candle holder of the same height sits in a box in the basement for eleven months of the year, and that's a real cost nobody counts at the time of purchase.
Construction — facts
| Number of parts |
three: base, silhouette plate, stabilizing fin |
| Sheet thickness |
3 mm on all three parts |
| Base |
24 cm diameter disc with four tealight sockets |
| Silhouette height |
24–30 cm depending on the design |
| Silhouette width |
15–30 cm; narrowest is the cauldron, widest is the bat |
| Stabilizing fin |
pointed arch 16 × 16 cm, identical across all eleven designs |
| Socket diameter |
40 mm, four sockets placed on the diagonals |
| Joining method |
cross-notch cut halfway into the plate and the fin, tabs set into slots in the base — no welds, no screws, no bending |
| Allowance for the coating |
the notches are cut at 3.2 mm instead of 3.0 mm, because the powder coating adds 60–80 µm on each side and without that allowance the joint would seize the first time you assemble it |
| Weight of the set |
1.83–2.49 kg depending on the design; the base and fin are a constant 1.32 kg |
| When disassembled |
three flat sheets, 9 mm thick in total, largest piece Ø 24 cm |
Candles and burn times — the facts
| Candle type |
tealight, i.e. a candle in an aluminum cup — the standard available in any supermarket |
| Tealight diameter |
38 mm in the European standard |
| Clearance in the socket |
the socket is 40 mm, which leaves 2 mm of clearance across the diameter and 1 mm all around — the tealight drops in without force and doesn't fall out when you move the holder |
| Tealight height |
16–18 mm; taller candles in a 22 mm cup will fit too, but they raise the flame 5 mm closer to the silhouette |
| Weight and wax |
about 15 g in total, of which 12–14 g is wax |
| Burn time of one |
about 4 hours |
| A set of four |
4 hours of light, because they burn at the same time; 16 hours is the total burn time and only tells you how much wax is used |
| What not to use |
candles in glass with a diameter over 40 mm can't be seated in the socket; taper and pillar candles have nothing to rest on here |
Heat and safety — the facts
The sockets sit on the diagonals of the base, not on the axes of the plates, and that's an engineering decision, not an aesthetic one. With a spacing radius of 70 mm and a 45° angle to both planes, the flame axis ends up 49 mm from the nearest sheet. If the sockets sat on the axes of the silhouette plate and the fin, that distance would be zero — the flame would burn directly under the edge of the steel.
| Flame axis to sheet |
49 mm in every direction, with the sockets spaced on the diagonals |
| Silhouette above the flames |
5 cm above the wick it reaches 85°C, 20 cm above the wick 45°C — the upper part of the silhouette stays cool, the lower part doesn't |
| Bottom of the aluminum cup |
near the end of burning, when almost no wax is left, it reaches 70–90°C |
| Base under the candles |
heats up from the cups and passes the heat on to the tabletop — put a trivet under the candle holder |
| What not to place nearby |
curtains, paper napkins, dried plant decorations and bottles of alcohol closer than 30 cm to the nearest flame |
| Unattended |
no — burning candles should never be left unattended, even in a metal candle holder |
What this candle holder won't do — before you buy
Toward the end of a burn, the bottom of the aluminum cup reaches 70–90°C, and that heat travels through the base into the tabletop. On oiled and lacquered wood it leaves a matte mark the size of the base that a cloth won't wipe away. Put a cork or felt pad under the candle holder; this isn't excess caution, it's simply because 3 mm steel conducts heat much better than glass or ceramic.
The silhouette above the flames heats up. Five centimeters above the wick the sheet metal reaches 85°C, which is above the pain threshold on contact — don't move the candle holder by the lower part of the silhouette while it's burning, and don't let children touch it. Once the candles are out it cools in a few minutes because there is little mass, but while burning it is a hot object.
The 60–80 µm powder coating is applied here without a zinc primer, because the product is intended for indoor use. On a terrace, a balcony or in an entryway where moisture condenses, the coating will start to wear at the edges and recesses after two or three seasons. If the candle holder is going to stand outdoors, this is the wrong choice — the same section of the shop has garden lanterns made for that purpose.
Four tealights give 4 hours of light, not sixteen. That's a number worth looking at before you commit: a full set lasts one evening, so keep a stock if guests are going to stay longer. A single tealight costs a few cents, but you need to have them at home on October 31.
The flame is visible from both sides of the silhouette only with designs that have a large open area. The cobweb is 70% open and you can see all four candles through it; the cat is 20% open and from behind it you see only a glow along the edges. That isn't a flaw in either of them, but if you buy a second piece it's worth knowing that these two designs behave differently.
Steel, glass and ceramic candle holder and paper lantern
|
3 mm steel |
Glass |
Ceramic |
Paper lantern |
| When knocked over |
tips over and stays in one piece |
shatters, shards scatter within 2 m |
cracks when it hits an edge |
bends and catches fire from the candle |
| Above the flame |
heats up to 85°C, keeps its shape |
cracks with uneven heating |
unchanged |
real risk of ignition |
| After 5 seasons |
same shade, 60–80 µm coating |
wax buildup in the corners |
glaze chips on the edges |
doesn't survive it |
| Removing wax |
wax comes off once cooled, the sheet metal doesn't scratch |
every streak shows |
wax gets into micro-cracks in the glaze |
can't be cleaned |
| Storage |
three flat sheets, 9 mm in a drawer |
a box for 11 months of the year |
box plus dividers |
folds up, but doesn't survive being folded |
| Number of seasons |
10 or more |
3–5 until it breaks |
3–5 until it chips |
1 |
| Cost per season over 10 years |
about €5.00 at a price of €49.78 |
about €6.52: €26.09 every 4 seasons |
about €7.61: €30.43 every 4 seasons |
about €8.70: €8.70 every season |
Frequently asked questions
Will ordinary supermarket tealights fit?
Yes — the socket is 40 mm and a standard European tealight is 38 mm, which leaves 2 mm of play on the diameter and 1 mm around the circumference. It goes in without force and doesn't fall out when you move the candle holder. Candles in glass over 40 mm in diameter don't fit, nor do taper and pillar candles, because they have nothing to rest against in the socket.
Won't the tabletop underneath get scorched?
It won't scorch, but it can dull the finish: toward the end of a burn the bottom of the aluminum cup reaches 70–90°C, and that heat travels through the steel base into the tabletop. On oiled and lacquered wood it leaves a matte mark the size of the base. Put a cork or felt pad under the candle holder — 3 mm steel conducts heat better than glass or ceramic.
Doesn't the steel get too hot?
Five centimeters above the wick the sheet metal reaches 85°C, and 20 cm above the wick 45°C, so the upper part of the silhouette stays cool and the lower part doesn't. While the candles are burning, don't move the candle holder by the lower part of the silhouette. Once the candles are out it cools in a few minutes because there is little mass in this sheet metal.
Can I put it on a windowsill next to a curtain?
Not closer than 30 cm to the nearest flame — and on a typical windowsill the curtain hangs closer than that. The same distance applies to paper napkins, dried plant decorations and bottles of alcohol. If the windowsill is the only spot, tie the curtain back or use LED candles, accepting a weaker, steady glow instead of a moving flame.
Can it be folded flat after the season?
Yes, in a matter of seconds, in the reverse order of assembly: take the silhouette panel and the fin out of the base, then slide them apart at the notch. You are left with three flat sheets with a combined thickness of 9 mm, the largest being a Ø 24 cm disc. The whole set takes up less space in a drawer than a dinner plate.
Is it suitable for a home with a cat?
The candle holder itself is — it weighs 1.83 to 2.49 kg and has a 24 cm diameter base, so a cat can't knock it over with a paw the way it can a glass one. The problem isn't the holder, it's four open flames at tabletop height: with a pet that jumps onto the table, LED candles are the only sensible solution. Burning candles should never be left unattended, no matter who lives in the home.
How do I clean wax off it?
Wait until the wax has set completely, then pry it off with your fingernail or a plastic scraper — it comes off the smooth powder coating in one piece and leaves no trace. Don't use a knife or metal scrapers, as the coating is only 60–80 µm thick and can be cut. Wipe off any residue with a cloth and a little dish soap; do not use abrasive cleaners.
If you're looking for a decoration that stands on the table and doesn't need any of the four candles, the right category is Halloween table decorations — it contains only products that stop working as intended without a flame.
If you're looking for the silhouette alone as a standing figure, without the candle base, check out metal decorative figurines, where the same motif is available without the base and without the 4 tealight slots.
All our other candle products — candelabras, hurricane shades, garden lanterns on a stake, torches and collars for a candle jar, that is 6 types besides this one — can be found in the parent category Metal Halloween Candle Holders and Lanterns.