Favorites
Tealight Holders

Product code: 31710

Bat Tea Light Holder – Halloween Bat

€51.96

  • PayPal
  • Visa
  • Mastercard
  • Google Pay
  • Apple Pay

Buying for a business or in larger quantities? Request a B2B quote

Bat Tea Light Holder – Halloween Bat

Four tealights set on the diagonals of the base light the silhouette from every side: the two front ones outline the cutouts, the two rear ones cast a glow along the edges. With 45% open area, what you mostly see behind the silhouette is the glow on the edges rather than the flames themselves. A set of four candles gives 4 hours of burn time, because they burn at the same time.

Silhouette

A bat with outspread wings perched on a cemetery gate pillar. The membrane between the wing bones is cut out separately, and the pillar, with its cornice and rustication, is marked by through-cuts.

Construction and assembly

Three flat 3 mm steel plates: a Ø 24 cm base, a plate with the silhouette and a 16 × 16 cm stabilizing fin. The plate and fin cross at a right angle on a notch cut halfway into each of them, and both lock into the base on tabs. The notches are cut at 3.2 mm instead of 3.0 mm, because powder coating adds 60-80 µm per side — without this allowance the joint would jam the first time you assemble it. Zero welds, zero screws.

Product details

What it's made of

Element Dimension Share of weight
Base with 4 sockets Ø 24 cm, sockets Ø 40 mm 0,95 kg
Silhouette plate 30 × 30 cm 1,17 kg
Stabilizing fin 16 × 16 cm 0,37 kg
Complete set 3 pieces, 3 mm steel 2,49 kg

Heat and safety

The flame axis sits 49 mm from the nearest plate, because the sockets lie on the diagonals of the base, not on the axes of the plates. The silhouette reaches 85°C 5 cm above the wick and 45°C 20 cm above it. The bottom of the aluminum cup is 70-90°C at the end of the burn, so put a coaster under the holder. Do not place curtains, napkins or dry decorations closer than 30 cm to the flame.

Durability and storage

The 60-80 µm powder coating in matte black keeps its shade for dozens of seasons; 3 mm steel doesn't dent when knocked over and doesn't warp over the flame. The product is intended for indoor use — the coating is applied without a zinc primer, so on a patio it will start to wear after two or three seasons. After the season, the holder breaks down into 3 flat plates with a combined thickness of 9 mm. The manufacturer is Metal4Home, a brand of Adjatech Metalworking Sp. z o.o., a maker of metal decorations based in Poznań.

Questions and answers

Frequently Asked Questions

Will ordinary supermarket tealights fit?

Yes — the holder is 40 mm, and a standard European tea light is 38 mm, so there is 2 mm of play on the diameter and 1 mm all around. Candles in glass over 40 mm, as well as taper and pillar candles, won't fit, because they have no support in the holder.

How many hours does the set burn?

Four hours. The four tea lights burn at the same time, so 16 hours is the total burn time and only describes wax consumption. One tea light holds 12-14 g of wax and burns for about 4 hours, so the set lasts one evening.

Won't the tabletop underneath get scorched?

It won't scorch, but it may dull: toward the end of the burn, the bottom of the aluminum cup reaches 70-90°C (158-194°F), and that heat passes through the steel base into the tabletop. On oiled and varnished wood it leaves a matte mark 24 cm in diameter — put a coaster under the candle holder.

Does the silhouette get hot?

Five centimeters above the wick the sheet metal reaches 85°C (185°F), and 20 cm above the wick it reaches 45°C (113°F), so the upper part of the silhouette stays cool and the lower part does not. The flame axis sits 49 mm from the nearest plate, because the holders are placed on the diagonals rather than on the axes — with an on-axis layout it would be zero.